Bearhawk
Parts For Sale by Bearhawk Aircraft
Bearhawk Aircraft has been manufacturing kits and parts for the Bearhawk since 2001. In 2009, we started manufacturing kits & parts for the Patrol. All parts manufactured by Bearhawk Aircraft are made under the supervision and authorization of Bob Barrows, design engineer of the Bearhawk & Patrol. |
|||
The parts prices and packing/shipping charges are listed separately. If you use PayPal, the packing/shipping prices will be automatically added. |
|||
1 All the parts on certain pages of the plans are offered as a package. This will include all the parts needed for one Bearhawk even though the picture might just have one example of a certain part. |
2 While the parts in the pictures are mostly primered and painted as we deliver them in the QB kits, in an effort to keep the prices as low as possible they can be sold unpainted only oiled. If you would like, you can order your parts sandblasted, primered, and painted – we use Mil-P-23377F strotium chromate epoxy primer and then top coat with Mil-C-22750D epoxy grey paint. |
3 There are a few small bushings that the plans call for that are not in the pictures. These bushings will be included with the parts where they are used. |
4 All parts are made to order. They will be made and shipped on the next truck that brings our QB kits in order to keep transport costs low. Kit shipments are every 6 to 8 weeks. |
Plans #11 package – 6 parts total consisting of: 2 Aileron support frames 2 Aileron bellcranks 2 Aileron pushrods (5/16 threads both sides) |
Plans#11
package – Unpainted $432.48 + $25 S&H Plans
#11 package – painted -$474.88 + $25 S&H |
Plans #12 package – 10 parts total consisting of: 2 Flap support frames 2 Flap torque tubes w/inboard lever 2 Flap pushrods 4 Flap arms |
Plans#12 package Unpainted $366.76 + $25 S&H Plans#12 package Painted $403.86 + $25 S&H |
Plans #13 package – 30 parts totalconsisting of: 4 Aileron hinges-inboard 4 Aileron hinges-outboard4 Flap hinges-center 8 Flap hinges-inboard & outboard 2 Aileron hinge mount-inboard2 Aileron hinge mount-outboard4 Flap hinge mounts w/o hole 2 Flap hinge mounts w/hole |
Plans#13 package unpainted $447.32 + $20 S&H Plans#13 package painted $491.84 + $20 S&H |
Plans # 14 package – 8 parts totalconsisting of: 2 Aileron cable pulley brackets 4 Wing strut attach fittings 2 Inboard support tube s |
Plans#14 package unpainted – $360.40 + $20 S&H Plans#14 package painted – $396.44 + $20 S&H |
Plans #20 package – 4 parts totalconsisting of: Horizontal Stabs 2 (1L & 1R) Elevators 2 (1R & 1L) Not pictured but included with this package are all the trim system parts including the two push rods(not bent). |
Plans#20 package unpainted $842.70 + $70 S&H Plans#20 package painted $943.40 + $70 S&H |
Plans #21 package – 1 partconsisting of: 1 Rudder w/ tailwheel steering arm |
Plans#21 package unpainted $337.08 + $25 S&H Plans#21 package painted $371 + $25 S&H |
Plans #23 package – 2 parts consisting of: Landing gear 2 (1L & 1R) |
Plans#23 w/AviPro welded step – unpainted $757.90 + $45 S&H Plans#23 w/AviPro welded step – painted $833.16 + $45 S&H
Plans#23 w/o step (per plans)- painted $769.56 + $45 S&H |
Plans #25 package – 6 parts totalconsisting of: 2 Shock struts 2 3/4 Inner Tubes w/piston welded in place 2 Bronze Top caps |
Plans#25 package unpainted $715.50 + $30 S&H Plans#25 package painted $768.50 + $30 S&H |
Plans #26 package – 6 parts totalconsisting of: Control sticks 1 Control Stick frame1 Elevator bellcrank 1 Stick to bellcrank pushrod 1 Tube connecting stick bottoms |
Plans#26 package unpainted $428.24 + $22.50 S&H Plans#26 package painted $491.84 + $22.50 S&H |
Plans #27 package – 3 parts totalconsisting of: 1 Rudder pedal assembly 2 brake pedals |
Plans#27 package unpainted $303.16 + $22.50 S&H Plans#27 package painted $337.08 + $22.50 S&H |
Plans #28 package – 3 parts total consisting of: 1 Flap handle 1 T7 tube that goes inside handle 1 Aluminum flap guide |
Plans#28 package unpainted $201.40 + $15 S&H Plans#28 package painted $230.02 + $15 S&H |
Seats | ||
Front Seats frames(2) |
Front seats unpainted $340.26 + $22.50 S&H
|
![]() |
Rear Seat frame |
Rear seat unpainted $212 + $55 S&H Rear seat
painted $238.50 + $55 S&H |
![]() |
Fuel Tanks sets | ||
Main tanks (25 gal each) 2 (1L & 1R) |
Main fuel tanks $814 a pair + $65 S & H |
No picture available |
Aux tanks (11 gal) 2 (1L & 1R) |
Aux tanks $621.50 a pair + $45 S&H |
![]() |
Windshields |
||
Windshield – Standard Cessna 170 (requires trimming to fit Bearhawk) 3/16″ thickNote: All windshields are drop shipped directly from LPAero Plastics. Shipping and handling are normally $130 – $180Note 2: For information about the new UVB blocking windshields – download this pdf. |
p/n LP-312.187BHCL clear – $377.36 p/n LP-312.187BHGT green tint – $468.52 p/n LP-312.187BHSG solar gray tint – $458.98 p/n LP-312.187BH UV-GT UV Blocking green tint – $551.20 p/n LP-312.187BH UV-SG UV Blocking solar gray tint – $551.20 |
No picture available |
Windshield – Bearhawk (minor or no trimming required) 3/16″ thickNote: All windshields are drop shipped directly from LPAero Plastics. Shipping and handling are normally $90 – $105Note 2: For information about the new UVB blocking windshields – download this pdf. |
p/n LP-1663CL Clear – $377.36 p/n LP-1663GT green tint – $447.32 p/n LP-1663SG solar gray tint – $447.32 p/n LP-1663UV-GT UV Blocking Green Tint – $551.20 p/n LP-1663UV-SG UV Blocking Solar Gray Tint – $551.20 |
No picture available |
Bearhawk wing strut ends. Four required. Two upper (strut to wing) and two lower (strut to fuselage). Milled from 2024T351. |
Wing strut ends (4) $169.60 /set + $10 S&H |
![]() |
Bearhawk fuel line gascolator made from 6061T6 aluminum, minimum internal port size 5/16 inch diameter. Max operating pressure 150 psi. 2 1/2 inch diameter with 3 inch height. inlet and outlet are 1/4 NTP. 1/8 NPT for quick drain on bottom of bowl. Comes with extra O-ring set. Free shipping if you send BH plans number with order. |
Gascolator Assembly $83.21 |
![]() |
Fuel cap assembliesIncludes all viton O-rings & nylon washers |
Fuel cap |
![]() |
Gerdes short shaft brake master cylinders with special clevis end of 7075T6 which allows for max adjustment of length. Now overhauled w/all new orings and polished bore and shaft. |
|
![]() |
Tail wheel springs with U-clamp |
Tail wheel |
![]() |
Bearhawk/Patrol/LSA tailwheel assemblies. Complete with wheel, Aero Classic tire and tube. Available in 8″, 10″, or Tundra for either the Patrol or LSA (mount for Tapered Rod Spring) or Bearhawk (mount for 1 1/2″ Leaf Spring) |
Available at http://bhtailwheels.com
|
![]() |
Wing strut tie down rings |
|
![]() |
Bearhawk aileron bellcrank bearings – 4 required |
|
![]() |
Continental Motor Mounts |
||
Continental O-470 bed mount |
Cont. O-470 motor mount painted $847.21 + $35 S&H |
No picture available |
Lycoming Motor Mounts Note: Type I Dynafocal Engines have a 1 3/8″ opening in the mount adapters for the rubber isolators. Type II Dynafocal Engines have a 2′ opening in the mount adapters for the rubber isolators. |
||
Lyc O-540 Type I dynafocal |
Lyc. O-540 Type I motor mount painted $673.00 + $35 S&H |
![]() |
Lyc O-540 Type II dynafocal |
Lyc. O-540 Type ll motor mount painted $673.00 + $35 S&H |
No picture available |
Lyc O-360 Type I dynafocal |
Lyc. O-360 Type l motor mount painted $673.00 + $40 S&H |
![]() |
Trim Wheel 1/4″ Aluminum w/ 9 tooth sprocket installed |
Trim wheel – $42.40 + $7.50 S&H
Trim Wheel
|
![]() |
Aileron/Flap hinge rod ends Rod end bearings to mount your ailerons & flaps. Ten required for one Bearhawk |
Aileron/Flap hinge rod end The price is $21.20 each. Shipping would be $5.80 for one or the ten required. |
![]() |
AURORA ROD END BEARING PACKAGE for BEARHAWK | MM3 qty 2 GMM-3M-570 qty 8 XAM-7 qty 2 $170.76 + $6 S&H |
No picture available |
XAM-7M Aurora Rod Ends for shock struts |
Two (2) rod ends – $44.44 + $7.50 S&H |
![]() |
Cable guards for the aileron pulleys in the wings. Four pieces. All are drilled for 5/16″ hole pulleys. |
Cable guards set -$39.75 including S&H. |
![]() |
Rear Seat attachment bolts Two AN eye bolts (with bushings) for the rear seat attachment per Bob Barrows recommendation. For rear set of attach bolts only. Not needed for front set. |
Rear Seat attachment bolts – $12.72 (shipping included) |
![]() |
Tail Rib Package:All rudder, Vstab, Elevator, and Hstab ribs bent to spec and left long for fitting/welding. |
Tail Rib Package – $296.80 + $15 S&H |
No picture available |
Rib / Spar Web Package This package consists of all wing ribs, aileron ribs, flap ribs, and false ribs. Ribs are professionally hydroformed with lightening holes cut and flanged. The ribs will still need to be straightened and have the vertical stiffener angles installed. Included are all .032 spar webs for the main spars, rear spars, false spars, aileron spars, and flap spars. Also included are all the aluminum parts that need to be bent on an 8ft. brake. These consist of the wing trailing edge skin stiffeners in the flap area (4 pieces ) and the aileron/flap trailing edges ( 4 pieces ). Note: This package eliminates one of the harder tasks for the scratch builder – finding an 8ft. brake and bending the spar webs to match your ribs. |
Rib / Spar Web Package – $3500 + $175 S&H |
![]() |
Ribs alone All other ribs mentioned above except the four false ribs. |
Ribs alone – $2120 + $45 S&H |
No picture available |
Spar webs alone – |
Spar webs alone – $1378 + $130 S&H |
No picture available |
Bearhawk Aircraft now offers a tubing package for the basic fuselage. All tubes are full length(per plans), all bent to shape, and with all tube ends notched or “fishmouthed” to fit together. We assemble this package in our fuselage tooling, then remove the tubing, label each tube as to its correct location, and pack into a long cardboard tube for shipping. |
4-Place BH Tubing Package – $3300 + Please contact for shipping cost before ordering |
No picture available |