Bearhawk Patrol
Showing all 24 results
-
Plans #8 – AileronĀ Support Frames
$495.00– includes page #8 parts:
2 aileronĀ support frames2 aileron bellcranks
-
Plans #9 – Flaps
$455.00includes:
Flap support frames (2 pieces)
Inboard flap levers (2 pieces)
Flap arms (4 pieces)
Flap pushrods (2 pieces w/bushings) -
Plans #13 & 14 – Hinge Mount Flaps
$625.00– includes page #13 & #14 parts:
Hinge mount flap inboard & outboard
(4 pieces)
Hinge mount Flap center (2 pieces)
Flap inboard & outboard hinges
(4 sets of 2)
Flap center hinges (2 sets of 2)
Aileron hinges inboard (2 sets of 2)
Aileron hinges outboard (2 sets of 2)
Aileron hinge mounts outboard (2 pieces)
Aileron hinge mounts inboard ( 2 pieces) -
Plans #15 – Aileron Cable Pulley Bracket
$200.00includes:
Support tube (2 pieces)
Aileron cable pulley bracket (2 pieces) -
Plans #15a – Wing Strut Attach Straps
$120.00Wing strut attach straps – 4 pieces of .190 4130N sheet
-
Plans #16 – Wing Strut Ends
$180.00Wing strut ends milled out of 2024T4
(4 pieces) -
Plans #22 – Elevators
$1,550.00includes:
2 Hor Stabs (L&R)
2 Elevators (L&R) w/horns installed
2 trim horns
2 trim linkage parts installed
2 trim pushrods (straight) -
Plans #23 – Rudder Assembly
$525.00Rudder Assembly
-
Plans #24 – Horizontal & Vertical Stabilizer Ribs
$675.00Elevator & Rudder Ribs
11 airfoil shaped ribs
22 flat or tapered ribs -
Plans #26 – Landing Gear Legs w/ Step
$1,200.00Landing gear legs w/ welded step: 1 L & 1 R
-
Plans #28 – Shock Struts
$1,050.001 L & 1 R
2 pistons welded to shaft
2 Hard bronze top caps
Includes o-ring & snap ring kit -
Plans #29 – Control Stick Assy
$800.001 front stick
1 rear stick
Stick bases (front & rear) welded to 1.25x.035 torque tube
1 interconnect tube
1 idler arm -
Plans #30 – Rudder Pedals & Brakes
$300.002 front rudder pedals
2 rear rudder pedals
4 cable links for front pedals
4 cable links for rear pedals -
Plans #31 – Flap Control Assy
$395.001 Flap handle
1 Inner latch pin release assy
1 mount plate
1 aluminum flap position quadrant
2 .080 tabs -
Windshield – Patrol & LSA
$363.00 – $510.00(minor or no trimming required) 1/8″ thick
LP AeroPlastics windshields in UV-SG in Solar Gray tint and UV-GT green tint are now available in windshields and side windows. They block all of the UVB and 99% of the UVA radiation,Ā and 30% more of the Near Infrared radiation (heat) than standard tints.
Note: All windshields are drop shipped directly from LPAero Plastics. Shipping and handling are normally $130 – $180
-
Aurora Rod End Bearing Package for Patrol
$315.00MM3-2 qty 2; GMM-3M-470 qty 4; GMM-3M-570 qty 2; GMM-3M-680 qty 5; XAM-7 qty 2
-
Patrol\Companion Stainless Round Tail Spring
$130.00Heat treated to the proper hardness, and then machined to shape.Ā
-
Patrol Wing Strut Tie Down Rings
$25.00Tie down ring setĀ
-
Patrol Aileron Bellcrank Bearings
$6.364 required
Price $6.36 each + $8.20 S&H
-
Patrol Aileron Flap Mount Bearings
$7.4210 required
Price $7.42 each + $8.20 S&H
-
Patrol Spar Web and Rib Package
$4,150.00All spar webs of .032 2024T3 bent up to match the ribs we have professionally hydroformed. Includes webs for front wing spars , rear wing spars, flap spars, aileron spars, false spars aft of gas tanks, and false ribs(4). This package also includes all the parts that have to be bent on long brakes. These parts are the skin stiffeners aft of rear spar in the flap area, & trailing edge material.
-
Patrol Ribs Package
$2,750.00– includes all ribs for one Patrol including main ribs (.025 & .032), nose ribs, flap nose & main ribs, aileron nose & main ribs, pocket ribs, & trailing edge ribs. These ribs are professionally hydroformed in the 0 condition and then hardened to the T-351 spec
-
Patrol Spar Webs Only
$1,445.00Spar webs only along with all aluminum parts that require a 8 ft. or 10 ft. brake
-
Patrol Tubing Package
$4,050.00Due to 4130 tubing shortages right now – tubing packages are temporarily unavailable.
Bearhawk Aircraft now offers a tubing package for the basic fuselage. All tubes are full length(per plans), all bent to shape, and with all tube ends notched or “fishmouthed” to fit together. We assemble this package in our fuselage tooling, then remove the tubing, label each tube as to its correct location, and pack into a long cardboard tube for shipping.